Formuler Z Prime won`t show display display when Powered on

bilalpower1 · September 8, 2020 at 9:47 AM

Hello dear, i faced the issue in my formuler z prime device. When i powered on the device as regular it's start with power led on device after few second it's blinkings (red,green,red,green,red,green,red,green,red,green) 5 times in a row then led stable. I used to remote for change resolutions but not get result. My remote signal has been received on device surely. I tried to change hdmi, av cable & power adapter but no result been occurred. I also tried manual reset method using treads in forum page but won't work for me.

Hope you doing great effect for fix it.

Mevi · September 8, 2020 at 12:17 PM

Caps lock broken or?

bilalpower1 · September 8, 2020 at 1:10 PM

to understand easier

SAM · September 8, 2020 at 1:38 PM Official Post

Please edit into small/normal text and read forum rules. Constantly writing with Big letters is in forum language "yell".

SAM · September 9, 2020 at 7:50 AM Official Post

Quote from bilalpower1

i faced the issue in my formuler z prime device. When i powered on the device as regular it's start with power led on device after few second it's blinkings (red,green,red,green,red,green,red,green,red,green) 5 times in a row then led stable. I used to remote for change resolutions but not get result. My remote signal has been received on device surely. I tried to change hdmi, av cable & power adapter but no result been occurred. I also tried manual reset method using treads in forum page but won't work for me.

1. Try this to factory reset -> https://support.formuler.tv/kb/article/31-…znano-z-zprime/

2. No Signal -> https://support.formuler.tv/kb/article/10-…ust-resolution/

bilalpower1 · September 9, 2020 at 8:34 AM

Dear, i tried all above method but issue remain same. When i manual factory reset through USB " _recovery_facinit " file is not present in USB after whole manual rset process means it's done reset Right.. Also try Resolution method but display won't get. when i power ON Formuler Z Prime Red & Green Combination LED blinking then Stable on Green..

SAM · September 9, 2020 at 11:48 AM Official Post

Ok, means the factory reset was successful and with (red/green led flashing means the box boot, constant green led box is operational ) you only don`t have picture. Please try with other HDMI Cable and HDMI port on your TV,test again like in 2. Test also on other TV if possible.

bilalpower1 · September 9, 2020 at 9:17 PM

I checked & confirm that my device is now working but display still won't get. I tried to change couple of new HDMI cables & Also try " HDMI adaption method" but nothing works. But in Air Sync app I have shown Device working properly. So what I do now I think hardware issue.

SAM · September 9, 2020 at 11:08 PM Official Post

Before you give it to repair, test on other tv.

bilalpower1 · September 10, 2020 at 9:14 AM

Sir i have checked with two different TV but no Signal. Will they also connect via AV Cable? OR also refer which faults will be repair which cause HDMI No Display

SAM · September 10, 2020 at 6:18 PM Official Post

Ok if you did already few times what stays in the how to (resolution change) and HDMI still not work then this box could be defective.

Quote from bilalpower1

OR also refer which faults will be repair which cause HDMI No Display

This is something that i don`t know, i`m not from repair service It can be only the HDMI port or some other chip.

bilalpower1 · September 11, 2020 at 10:15 AM

Okay Thanks Again

Users Viewing This Thread